Paints & Protective Coatings for Mining
Mines and processing plants are among the hardest places a coating has to survive: abrasion, water, dust, chemical splash and heat, often all at once. Marindec has supplied mining, steel and farming customers in Southern Africa for more than 30 years, from 5L tins to 200L drums.
This page covers corrosion protection on mines: which of our protective coatings goes where, and what the technical data sheets (TDS) say about applying them.
Corrosion protection on mines
Steel on a mine rusts for the same reason it rusts anywhere: water and oxygen reach the metal. Mines speed that up with constant damp, abrasive dust that wears through the paint film, and knocks that expose bare steel.
Good corrosion protection comes down to three things: a clean surface, a primer that holds on to the metal, and enough film built over it. The right products depend on where the steel is, so the table below is organised by area.
Coating systems by area
| Area | Coating system | From the data sheet |
|---|---|---|
| Structural steel, headgear, conveyor gantries, plant frames | Two-pack (2K) high-build primer, ask us + 2K polyurethane | Polyurethane 35–45 µm dry film thickness (DFT), full cure ±7 days; needs a 2K primer, not an alkyd |
| Mobile equipment, chutes, machine frames | ZPPW15 + fast dry enamel, or AGRIP30+ high build on its own | Touch dry in about 10 minutes; next coat within 2 hours (AGRIP30+: 2–3 hours) |
| Hot pipework, flues, exhausts | Heat Resistant Aluminium | Continuous dry heat up to 540 °C; no undercoat |
| Camp roofs, galvanised sheeting and fencing | Galvanised Iron Primer + topcoat | 50–60 µm DFT; overcoat after overnight drying |
| Aluminium and other non-ferrous parts | EPS15 etch primer + topcoat | 10–15 µm DFT; overcoat after at least 1 hour |
| Workshop floors, walkways, demarcation lines | Floor & Stoep enamel, road marking paint | Floor enamel 35–50 µm DFT; marking paint to SANS 731-1 |
| Cleaning and stripping before painting | Armourphos Cleaner, Paint Remover | Paint only on dry, oil-free steel at least 3 °C above the dew point |
Gold mines and processing plants
Underground, steel stays damp for most of its life, and processing plants add splash, fumes and hot pipework. Plant steel needs a primer with an anti-corrosive pigment and a topcoat that stands up to sun and wash-down.
For structural steel and plant equipment that must hold its colour and gloss outdoors, finish with 2K polyurethane. Its datasheet calls for a two-pack (2K) high-build primer underneath, not an alkyd primer, so ask us for the primer when you order. For a single-pack system, use ZPPW15, a fast-drying alkyd primer with a zinc-modified phosphate anti-corrosive additive, under fast dry enamel or AGRIP30+.
Armourthane 50 is a two-pack aliphatic acrylic polyurethane. Mix 7 parts base to 1 part curing agent and use it within about 4 hours at 23 °C. It is hard dry in about 8 hours and fully cured after about 7 days, so plan the return to service around that.
Hot pipework, flues and exhausts take Heat Resistant Aluminium, a silicone-resin finish rated for continuous dry heat up to 540 °C. It reaches full properties only after baking or once the steel comes up to operating temperature.
For tank linings, immersion service or constant acid or alkali splash, send us the conditions before choosing a system. We'll tell you plainly whether a product in our range fits.
Mining camps and housing
On a mining camp, the roofs and the steel around them need different primers. Galvanised roof sheeting and zinc-coated fencing take Galvanised Iron Primer, because red oxide primers lose adhesion on zinc.
Clean off white rust and dirt before priming galvanised sheeting, as set out in the IBR roof sheeting guide. Galvprime 35 goes on at 50 to 60 µm DFT and is ready for its topcoat the next day.
Mild-steel roof trusses, frames, gates and fences take ZPPW15 primer and then a fast dry enamel or AGRIP30+ topcoat. Where steel is already painted, scrape back loose paint, spot-prime the bare metal and topcoat the whole area.
Mining equipment and steel structures
Machines get knocked, scraped and washed down, so they need repainting more often than fixed steel. Fast-drying single-pack systems suit them, because a machine can be primed and topcoated in one shift.
AGRIP30+ is a primer and finishing enamel in one, with an anti-corrosive additive. On clean steel it needs no undercoat unless you are building a thicker film, and it takes the next coat within 2 to 3 hours.
The alternative is ZPPW15 under a fast dry enamel: both touch dry in about 10 minutes and take the next coat within 2 hours. The mining machinery repaint guide walks through it step by step.
Headgear, conveyor gantries and other large steelwork follow the same primer-and-topcoat logic on a bigger scale. See how to paint structural steel for building a full coating system. Primers for fabricated steel are covered on the steel fabrication page.
Preparation decides how long it lasts
- Blast exterior and wet-area steel to Sa 2½ (near-white metal) and prime it the same day, before flash rust forms. See steel surface preparation.
- Remove oil and grime with Armourphos Cleaner, and strip failed coatings back to sound metal with Paint Remover.
- Paint only when the steel is dry and at least 3 °C above the dew point. The data sheets for all of these primers and enamels set this condition.
- Stripe-coat edges, welds and bolts first. That's where corrosion starts.
- Build to the data sheet film thickness and check it with a gauge. A film that is too thin lets the steel's profile peaks rust through, as the film thickness guide explains.
- Plan maintenance: spot-repair damage early, before rust undercuts the coating.
Safety colours
Mining equipment and plant are commonly specified in SANS 1091 colours. Marindec lists Signal Red A11 in fast dry enamel and in AGRIP30+, plus Golden Yellow B49, Dark Admiralty Grey G12 and more.
See the full SANS colour chart. Fleet and corporate colours can be matched to RAL.
Supply for mines and contractors
Marindec manufactures in Alrode, Alberton (Gauteng), for collection or delivery nationwide, with regular supply to Gauteng, Mpumalanga and the Western Cape. Primers and enamels come in 200L drums for spray and dip plants as well as smaller packs.
See delivery and supply areas, bulk paint supply and the anticorrosive coating systems guide.
Request a quote with the equipment or area, the environment and the volume. Quotes usually come back the same working day.