Warehouse Floor Marking Paint & Coatings
In a warehouse, paint does practical work: it keeps pedestrians out of forklift lanes, marks racking aisles and loading bays, and protects the steel building. Marindec makes warehouse floor marking paint and the steel coatings for warehouses and distribution centres.
Warehouse floor marking paint
Marindec makes two paints for marking warehouse floors. Floor & Stoep Enamel is a single-pack, medium hi-build gloss enamel for concrete floors, walkways and aisle lines. It is usually applied without a primer once the floor is thoroughly clean. Road marking paint to SANS 731-1 builds a thicker line, at 150 µm dry, and dries faster.
Floor & Stoep Enamel is listed online in Green IG237 and Redox 130 5L tins. Its standard colours are Clear, White, Black, Redox 130, Green IG237, Mid Yellow M11G, Signal Red A11, Dark Admiralty Grey G12 and Battleship Grey. Other SANS or RAL colours are made to order.
Floors and demarcation
| Job | Product | Key figures (TDS) |
|---|---|---|
| Aisle lines, walkways, bay numbers | Road marking paint, Type 2 general application | 150 µm DFT; 4–5 m²/L; no pick-up in under 15 min, hard dry 45 min |
| Whole-floor colour, pedestrian zones, stoeps | Floor & Stoep paint | ~7.5 m²/L at 45 µm; touch dry 45–60 min; hard dry 4–8 h |
| Safety zones and hazard markings | Signal Red A11, Golden Yellow B49 and other SANS colours | Made to order in other SANS and RAL colours |
Plan floor marking around shifts. Lines can be walked on quickly, but leave forklifts off until the paint is hard dry. On concrete, remove dust, oil and curing compound first, and make sure the floor is dry. See surface preparation.
Applying floor marking paint
These steps follow the Floor & Stoep Enamel datasheet.
- Clean the concrete: remove dust, oil and curing compound. The floor must be dry and at least 3 °C above the dew point.
- Mask the lines. Brush or roller suits lines and small areas; airless spray is preferred for large areas.
- Apply 35–50 µm dry per coat, which is 100–140 µm wet. If needed, thin with GP or QD thinner, up to 15% for brush or roller and 10% for air spray.
- Recoat within 3–4 hours. It is touch dry in 45–60 minutes and hard dry in 4–8 hours.
Keep forklifts off until the paint is hard dry. Check the wet film with a gauge as you go; the film thickness measurement guide shows how.
The building and equipment
- Steel portal frames, columns and dock levellers: anticorrosive primer + enamel systems
- IBR roof sheeting and cladding: Galvanised Iron Primer first. See the IBR sheeting guide.
- Trailers, refrigerated units and truck bodies: transport enamel
- Gates, fencing and bollards: Fast Dry Enamel in safety colours
How much paint for floor lines?
Floor & Stoep Enamel covers about 7.5 m² per litre at 45 µm in theory. That is about 375 m of 100 mm line from a 5L tin. The datasheet says real coverage is 50–70% lower, depending on the floor and how the paint is applied, so plan on about 110–190 m of 100 mm line per 5L tin per coat. Rough or porous concrete takes more.
At 150 µm, a 5L tin of road marking paint covers about 20–25 m², roughly 200–250 metres of 100 mm line. More detail in the road marking guide.
Supply and delivery
Marindec manufactures in Alrode, Alberton (Gauteng), for collection or delivery nationwide, with regular supply to Gauteng, Mpumalanga and the Western Cape. See delivery and supply areas.
Request a quote with the equipment or area, the environment and the volume. Quotes usually come back the same working day.