Guides / Application guide

Steel Surface Preparation Before Painting

Metal and steel surface preparation for painting: cleaning methods, ISO 8501-1 and SSPC grades, and how to prepare galvanised iron, aluminium and concrete.

This guide covers metal and steel surface preparation for painting: which cleaning method to use, the cleanliness grade each method reaches, and what Marindec's datasheets require before the primer goes on. Steel comes first, then galvanised iron, aluminium, concrete and previously painted surfaces.

General rule

A substrate must be clean and mechanically sound before any primer or topcoat is applied. Painting onto dust or oil contamination causes the film to bond to the contaminant, not the substrate — resulting in adhesion failure regardless of the coating used.

Surface preparation methods

There are four main methods, used alone or one after another. Solvent cleaning always comes first, because brushing or blasting an oily surface only spreads the oil.

Solvent cleaning (degreasing) removes oil, grease, cutting fluid and marker. Wipe with a hydrocarbon solvent such as lacquer thinner or xylene on clean, lint-free cloths, change the cloths often, and let the solvent evaporate fully. It does not remove rust or mill scale.

Hand tool cleaning uses wire brushes, scrapers and abrasive paper to remove loose rust, loose mill scale and flaking paint. Tightly bonded scale and rust stay behind, so it suits small areas, touch-ups and mild indoor conditions.

Power tool cleaning uses rotary wire brushes, grinding and sanding discs, and needle guns. It is faster and more thorough than hand tools, and is the usual choice for spot repairs where blasting isn't possible. Don't polish the steel smooth: the primer needs some roughness to grip.

Abrasive blasting (grit or sand blasting) drives abrasive at the steel with compressed air. It is the only method that removes all mill scale and rust, and it leaves a rough anchor profile for the primer. Remove the blast dust and prime before flash rust forms.

Burn-off, heating the steel to about 400 °C, removes organic contamination but leaves a residue. Always follow it with mechanical cleaning.

Cleanliness grades: ISO 8501-1 and SSPC

ISO 8501-1 grades prepared steel by how clean it looks, against reference photographs. St grades are for hand and power tool cleaning, and Sa grades for blast cleaning. The American SSPC standards (now published by AMPP) cover the same ground; the closest equivalents are below, but they are not identical, so work to the grade your specification names.

MethodISO 8501-1SSPCWhat's left and when to use it
Solvent cleaningNoneSP 1Oil and grease removed; no visual grade. Before every other method.
Hand tool cleaningSt 2SP 2Loose rust, scale and paint removed. Small areas and touch-ups.
Power tool cleaningSt 3SP 3As St 2, more thoroughly, with a metallic sheen. Spot repairs where blasting isn't possible.
Brush-off blastSa 1SP 7Loose material removed; tight scale and rust stay. Light cleaning.
Commercial blastSa 2SP 6Most scale and rust removed; firmly bonded traces remain.
Near-white blastSa 2½SP 10Only slight stains left. Marindec's recommended minimum for industrial and exterior steel.
White metal blastSa 3SP 5Uniform bare metal. The most demanding specifications.

The starting condition matters too. ISO 8501-1 rates uncoated steel from rust grade A (mill scale still intact) to D (rusted and pitted), and the photographs combine both: "D Sa 2½" is pitted steel blasted to near-white.

Ferrous metals (mild steel, structural steel, iron)

Contaminants to remove: millscale, rust, iron oxide, oils, grease and dust. Choose the method from the table above by how contaminated the steel is and where it will be used.

Recommended minimum for industrial and exterior environments: solvent clean, then grit blast to Sa 2½ (near-white metal).

Recommended minimum for interior and standard environments: solvent clean, then a mechanical scrub with hand or power tools (St 2 or St 3).

Conditions on the day

Marindec's primer datasheets, for FPW15, GI Primer and the EPS15 etch primer, set the same condition. The surface must be dry, free of dirt, dust and oily residue, at least 3 °C above the dew point, and cleaned by sandblasting or with sandpaper.

  • Paint only when the steel is at least 3°C above the dew point. Below that, moisture condenses on the surface and the primer bonds to water, not metal.
  • Prime blasted or wire-brushed steel the same day, before flash rust forms.
  • Remove all blast dust and wipe oily areas with solvent just before priming.

Products for preparation

Next step: choose the right primer for the metal with the primer selector, or see the full anticorrosive coating system.

Galvanised iron and zinc-coated steel

New galvanised surfaces:

Zinc coating produces white rust (zinc hydroxide carbonate) on exposure to air. This must be removed before painting:

  1. Clean with galvanised iron cleaner or sugar soap solution
  2. Rinse thoroughly with water
  3. Allow to dry completely before priming

Weathered galvanised surfaces:

Lightly abrade the surface to remove the chalk layer that forms with age, then clean as above.

Do not use red oxide primer on galvanised steel — use GI Primer formulated for zinc-coated substrates.

Aluminium

Aluminium forms a colourless oxide layer naturally. This must be addressed before painting:

  1. Solvent clean with a hydrocarbon solvent to remove oils
  2. Lightly abrade with fine abrasive paper to break the oxide layer
  3. Do not leave the surface exposed for extended periods between cleaning and priming

Do not use red oxide primer on aluminium — use an etch primer formulated for non-ferrous metals.

Concrete and masonry

  • Remove efflorescence (white powdery salt deposits) with a stiff brush; acid wash if heavily affected
  • Fill blow holes and surface cracks with an appropriate filler and allow to cure
  • Allow new concrete a minimum of 28 days to cure before painting
  • Ensure the surface is completely dry — test by taping a sheet of plastic to the surface and leaving for 24 hours; condensation indicates retained moisture

Previously painted surfaces

Before repainting any previously coated surface:

  1. Remove loose, flaking, or peeling paint with a scraper or wire brush — spot areas only, not total stripping unless the existing system is wholly unsound
  2. Feather back the edges of sound paint at the scrape boundaries with abrasive paper
  3. Clean the entire surface with sugar soap or detergent solution
  4. Rinse thoroughly and allow to dry completely
  5. Apply primer to any bare metal or exposed substrate before topcoating

Download the PDF guide

Working on a project like this? Request a quote — same-day turnaround on most requests.